ParaZapper™ MY Specifications ( preliminary )

The ParaZapper™ MY ( Many in One Zapper ) is a crystal controlled, microprocessor based, multi-frequency zapper designed with improved results in consideration. This zapper includes eight Rife frequency modes in one package at an affordable cost. It also provides a constant 10.5 volt ( +/- 0.25 V ) output without the risks associated with using a wall adapter. The output is strong and this unit is intended for those uses that need a stronger output as well as more numerous and more accurate frequencies. It also includes new innovations, such as pedestal offset, that offer significant enhancements over other zappers. It has a timer with a beeper to let you know when your cycle is done. It even includes a favorite mode option that allows you to set it to start up in any of the modes provided. While the frequencies contained in this zapper are very specific to certain organisms, it should also be effective as a general purpose zapper according to Dr. Clark's statements. For that reason, we have selected 15 Clark Frequencies in the 1 kHz to 2.5 kHz range and 66 of the most important Rife frequencies to provide the greatest flexibility and the best available coverage in an economical unit. The frequencies are as follows.

ParaZapper Customer comments

MODE Frequencies Duration
Mode 1 Rife Mode 1
Freq 1 72 +/- 0.25 Hz
Freq 2 727 +/- 1 Hz
Freq 3 95 +/- 0.25 Hz
Freq 4 776 +/- 2 Hz
Freq 5 120 +/- 0.5 Hz
Freq 6 787 +/- 2 Hz
Freq 7 432 +/- 1 Hz
Freq 8 800 +/- 2 Hz
Freq 9 465 +/- 1 Hz
Freq 10 802 +/- 2 Hz
After cycle completion, the unit will stop and beep,
then the unit will wait 5 seconds and repeat the same mode

Mode 1 will blink the Mode/Battery LED 1 Flash every 2 seconds

This mode will Show

BLK
BLK
RED
on the Mode LEDs

Note that due to the accuracy of the microprocessor generated signal,
most units are within 2 Hz of the specified frequency in this range.

The total cycle time is 35 minutes.

This mode contains the 10 most frequently used
Rife frequencies at 3.5 minutes each.
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
Mode 2 Rife Mode 2
Freq 1 500 +/- 1 Hz
Freq 2 880 +/- 1 Hz
Freq 3 600 +/- 1 Hz
Freq 4 1552 +/- 2 Hz
Freq 5 650 +/- 1 Hz
Freq 6 1865 +/- 3 Hz
Freq 7 660 +/- 1 Hz
Freq 8 2008 +/- 3 Hz
Freq 9 676 +/- 1 Hz
Freq 10 2128 +/- 3 Hz
After cycle completion, the unit will stop and beep,
then the unit will wait 5 seconds and repeat the same mode

Mode 2 will blink the Mode/Battery LED 1 Flash every 2 seconds

This mode will Show

BLK
RED
BLK
on the Mode LEDs

Note that due to the accuracy of the microprocessor generated signal,
most units are within 3 Hz of the specified frequency.

The total cycle time is 35 minutes.

This mode contains an additional set of 10 Rife Frequencies
intended to augment the 10 Rife frequencies in Mode 2 ( Rife Mode 1 ).
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
Mode 3 Rife anti bacterial 1
Freq 1 20 +/- 0.1 Hz
Freq 2 465 +/- 1 Hz
Freq 3 866 +/- 2 Hz
Freq 4 664 +/- 1 Hz
Freq 5 690 +/- 1 Hz
Freq 6 727 +/- 1 Hz
Freq 7 787 +/- 1 Hz
Freq 8 832 +/- 2 Hz
Freq 9 800 +/- 2 Hz
Freq 10 880 +/- 2 Hz
Freq 11 1550 +/- 3 Hz
Freq 12 784 +/- 2 Hz

After cycle completion, the unit will stop and beep,
then the unit will wait 5 seconds and repeat the same mode

Mode 3 will blink the Mode/Battery LED 1 Flash every 2 seconds

This mode will Show

RED
BLK
BLK
on the Mode LEDs

Note that due to the accuracy of the microprocessor generated signal,
most units are within 2 Hz of the specified frequency.

The total cycle time is 42 minutes.

This mode contains the set of frequencies most commonly called for
in the Rife list to kill bacteria.
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
Mode 4 Rife anti fungal 1
Freq 1 72 +/- 0.25 Hz
Freq 2 254 +/- 0.5 Hz
Freq 3 422 +/- 1 Hz
Freq 4 582 +/- 1 Hz
Freq 5 1016 +/- 2 Hz
Freq 6 1134 +/- 2 Hz
Freq 7 374 +/- 1 Hz
Freq 8 697 +/- 1 Hz
Freq 9 743 +/- 2 Hz
Freq 10 339 +/- 1 Hz
Freq 11 465 +/- 1 Hz
Freq 12 1550 +/- 2 Hz

After cycle completion, the unit will stop and beep,
then the unit will wait 5 seconds and repeat the same mode

Mode 4 will blink the Mode/Battery LED 1 Flash every 2 seconds

This mode will Show

BLK
RED
RED
on the Mode LEDs

Note that due to the accuracy of the microprocessor generated signal,
most units are within 2 Hz of the specified frequency.

The total cycle time is 42 minutes.

This mode contains the set of frequencies most commonly called for
in the Rife list to kill yeast, mold, fungi.
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
Mode 5 Rife anti viral 1
Freq 1 2489 +/- 3 Hz
Freq 2 727 +/- 2 Hz
Freq 3 329 +/- 1 Hz
Freq 4 802 +/- 2 Hz
Freq 5 1550 +/- 3 Hz
Freq 6 444 +/- 1 Hz
Freq 7 787 +/- 2 Hz
Freq 8 2128 +/- 3 Hz
Freq 9 800 +/- 2 Hz
Freq 10 465 +/- 1 Hz

After cycle completion, the unit will stop and beep,
then the unit will wait 5 seconds and repeat the same mode

Mode 5 will blink the Mode/Battery LED 1 Flash every 2 seconds

This mode will Show

RED
BLK
RED
on the Mode LEDs

Note that due to the accuracy of the microprocessor generated signal,
most units are within 3 Hz of the specified frequency.

The total cycle time is 35 minutes.

This mode contains the set of frequencies most commonly called for
in the Rife list to kill various virus forms.
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
Mode 6 Rife anti worm
Freq 1 +/- 5 Hz
Freq 2 +/- 7 Hz
Freq 3 +/- 5 Hz
Freq 4 +/- 5 Hz
Freq 5 +/- 5 Hz
Freq 6 +/- 5 Hz
Freq 7 +/- 5 Hz
Freq 8 +/- 7 Hz
Freq 9 +/- 6 Hz
Freq 10 +/- 6 Hz
Freq 11 +/- 6 Hz
Freq 12 +/- 6 Hz

After cycle completion, the unit will stop and beep,
then the unit will wait 5 seconds and repeat the same mode

Mode 6 will blink the Mode/Battery LED 1 Flash every 2 seconds

This mode will Show

RED
RED
BLK
on the Mode LEDs

Note that due to the accuracy of the microprocessor generated signal,
most units are within 3 Hz of the specified frequency.

The total cycle time is 12 minutes.

This mode contains the set of frequencies most commonly called for
in the Rife list to kill round worms, and flatworms.
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
3.5 min
Mode 7 Clark 1.0 - 2.5 kHz range
Freq 1 1000 +/- 2 Hz
Freq 2 2350 +/- 3 Hz
Freq 3 1250 +/- 2 Hz
Freq 4 2300 +/- 3 Hz
Freq 5 1500 +/- 2 Hz
Freq 6 2100 +/- 3 Hz
Freq 7 1600 +/- 2 Hz
Freq 8 2175 +/- 3 Hz
Freq 9 2050 +/- 3 Hz
Freq 10 2150 +/- 3 Hz
Freq 11 1600 +/- 2 Hz
Freq 12 2075 +/- 3 Hz
Freq 13 2458 +/- 3 Hz
Freq 14 2006 +/- 3 Hz
Freq 15 2059 +/- 3 Hz
After cycle completion, the unit will stop and beep,
then the unit will wait 5 seconds and repeat the same mode

Mode 7 will blink the Mode/Battery LED 1 Flash every 2 seconds

This mode will Show

RED
RED
RED
on the Mode LEDs

Note that due to the accuracy of the microprocessor generated signal,
most units are within 3 Hz of the specified frequency.

The total cycle time to produce all 15 frequencies is 15 minutes.

This mode will through the production of harmonics, reach 97 percent of the frequencies
provided in Dr. Hulda Clark's frequency list within a narrow margin.
1.0 min
1.0 min
1.0 min
1.0 min
1.0 min
1.0 min
1.0 min
1.0 min
1.0 min
1.0 min
1.0 min
1.0 min
1.0 min
1.0 min
1.0 min
Note: The frequencies in this unit are far more accurate than
the frequencies in Rife units that select the frequency using a dial,
unless a digital readout is used.

Note: While the frequencies listed for this unit are expected to be for certain parasites, there have not been any scientific tests run to validate that these frequencies actually have any effect on those specific parasites or any other parasites for that matter. This unit is only presented as a tool for experimentation.

While the unit has automatic timing and recycling for each frequency, it does not feature an automatic shutdown so that it can be used for continouos zapping. Power to the unit is supplied by a Alkaline or special Rechargeable 9-volt battery and is controlled by a push-on / push-off switch. The output voltage is 10.5 volts and the battery is functional depleted before requiring replacement or recharging. This helps to avoid connecting the zapper to wall power which can be dangerous. Frequency selection is by momentary contact push button switch. To change modes, simply press the mode switch. The battery and mode LED's will both come on at the same time. Release the switch and the next mode will start.





Description of Indicators ( Status, Mode/Battery ) and switches (ON/OFF) and Mode (mode change)

Power ON switch: (ON/OFF Button)
When the ON/OFF switch is pressed, the unit will come on and always starts out in the Favorite Mode which in a new unit, is Mode 1. The user may change the Favorite mode to any other mode at any time. Once a new favorite mode has been set, the unit will always start up in that mode.


Status LED: (Status) located nearest the On/Off button
The status LED can be used to monitor normal operation and also to test the unit for correct operation. The Status LED will normally appear yellowish or orange but there are exceptions. If the battery is completely dead or missing, the LED will be off or dark. If for some reason, the output fails, the LED will either be solid green or red.
To test the unit when operating, the unit should be on and operating with the copper paddles connected but not touching each other. In this condition, the LED will appear yellow or amber because it is flickering between red and green. A Red Status may indicate that the paddles are shorted together, however, if the red and green paddles are not shorted, a completely red Status means that you need to contact the factory for service.
Touching the copper paddles together should cause the LED to show almost completely red due to the current load being pulled by the short circuit. This is an indicaton that the zapper output is functioning properly and providing sufficient output for best results.
In certain frequencies ( 20 Hz and lower ), the RED and GREEN LEDs will ppear to flicker because of the low frequency. The LEDs actually flicker in all modes but they flicker faster than the eye can perceive.


Mode change switch: ( MODE button )

When the unit is first turned on, it starts in the Favorite Mode each time. The unit is shipped with the favorite mode set to mode 1.
Pressing this [Mode] button at any time will change from the current mode to the next mode in sequence and will also restart the timer.

Favorite Mode
When changing modes, if the Mode button is pressed for more than 2 seconds, the unit will beep and Favorite Mode will be erased. After the mode button is released, the unit will jump to mode 1 if the Favorite mode has been erased, otherwise, the unit will restart in the Favorite mode that was selected. If the Favorite Mode has been erased and this process is repeated, the selected frequency will become the Favorite Mode and the unit will start in that mode each time the unit is turned on.

Each time that the [Mode] switch is pressed, it will cycle to the next mode which can be observed by watching the Mode LEDs for the pattern produced.

The Mode/Battery LED will flash either one or two flashes every 2 seconds.

Mode 1 through 7 will produce a quick Flash every 2 seconds
2 Flashes every 2 seconds in Mode 8

Mode LED: (Battery / Mode) which is the Lower LED
The mode LED flashes once or twice per every 2 seconds.

Mode indicator array

RED
BLK
BLK
consists of 3 RED LEDs that are turned on or off to show a code for the mode that it is currently operating in as described in the Mode table above.

zapper

Hulda Clark Zapper is
not FDA approved for human or animal use.

Due to FDA restrictions,
Hulda Clark Zappers are not sold or intended for
human use or on animals.

The zappers below are intended to be used to lower levels
of bacteria, parasites, and other organisms in standing
water such as cooling towers, ponds, fountains, water containers, or similar water tanks, but may be used for other purposes if the user so wishes.

Zappers may also be used for checking oscilloscopes
or items such as small loud speakers,
but not for calibration purposes.

By purchasing any zapper or accessory from this site
you are agreeing that these products are sold
"not intended for use on humans or animals".

Not sold for use with drinking water, potable water,
in swimming pools, or for food preparation.

ParaZapper™MY

Not available yet, expected by Nov. 30, 2010

Not sold for use on humans or animals due to FDA requirements.

For the user who wants more frequencies and power.
With Stronger output than standard zappers, multiple repeating frequency cycles ion each range, Low Battery Indicator, Dual Frequency ranges, and a multicolor Status Indicator.

This is a multi-frequency zapper that is expected to provide better overall results.
Instructions for use on humans are not included but are available.

 

This model not available yet

 



Warranty
Satisfaction
Privacy		 About

us		 Shipping Technical

information		 Other zapper products

Usage

Using these devices for eliminating parasites from water is easy but is not 100 percent effective.
Before and after microscopic examination of pond water samples show significant reduction of microbial content after usage.

Normal application is to place the electrodes into the water, further apart is better.
The unit is then turned on 7 minutes and off for 20 minutes and repeated 3 or 4 times.

Do not use for drinking water, potable water, or in swimming pools.


Contact Webmaster:
Contact Sales: sales@paradevices.com

Our normal phone hours are 9:30 AM to 3:00 PM Central time weekdays
however, if you need to reach us at other times, call anyway.
We do not take orders by phone and can not make recommendations for use with humans or animals.
If we are not in, leave a name and phone number, we will call back.

Phone# 1-866-765-5116 Nationwide Tollfree
--or-- 205-856-3909 Alabama Local
Both numbers are for the same phone line.



ParaZapper is a trademark of
Para Systems, Inc.
5537 Balboa Ct.
Lower Entrance
Pinson, AL 35126 USA
All rights reserved.

Notice: On advice of counsel, we are required to inform you that the statements and claims on this web site have not been evaluated by the Food and Drug Administration and are not intended to diagnose, treat, cure or prevent any disease -- not for use on humans or with pets. These battery powered devices are not offered or intended for human use or to diagnose or prescribe for medical or psychological conditions nor to claim to prevent, treat, mitigate or cure such conditions, nor to recommend specific products as treatment of disease or to provide diagnosis, care, treatment or rehabilitation of individuals, or apply medical, mental health or human development principles. The devices discussed herein have not undergone evaluation and/or testing by the United States Food and Drug Administration or like agency of any other country. Risks that might be determined by such testing are unknown. The information on this site is not a substitute for medical or veterinary advice.





Historical references
parazapper.com
paradevices.com
hulda-clark-parasite-zapper.com

visits to this page

parazapper site visits