ParaZapper™ M-1 Specifications

The ParaZapper™ M-1 is a microprocessor based multi-frequency zapper designed with improved results in consideration. One frequency alone does not provide the best overall coverage for multiple types of micro-organisms. Two frequencies can double the chance of hitting a particular organisms resonance, but even this does not provide the best coverage. For that reason, we have selected 32 of the most important Rife frequencies to provide the best available coverage in an economical unit. The frequencies are as follows.

MODE	Frequencies	Duration
Mode 1	Rife 2.0 - 3.0 kHz range Freq 1 2280 +/- 10 Hz Freq 2 2127 +/- 10 Hz Freq 3 2489 +/- 10 Hz Freq 4 2720 +/- 10 Hz Freq 5 2170 +/- 10 Hz Freq 6 2008 +/- 10 Hz Freq 7 2250 +/- 10 Hz Freq 8 2050 +/- 10 Hz Stop and off 5 seconds, 3 - 1 second pulses and repeat Mode 1 will blink 1 Flash every 2 seconds Note that due to the accuracy of the microprocessor generated signal, most units are within 1 Hz of the specified frequency.	3.5 min 3.5 min 3.5 min 3.5 min 3.5 min 3.5 min 3.5 min 3.5 min
Mode 2	Rife Low range Freq 1 444 +/- 5 Hz Freq 2 333 +/- 5 Hz Freq 3 465 +/- 5 Hz Freq 4 128 +/- 5 Hz Freq 5 332 +/- 5 Hz Freq 6 143 +/- 5 Hz Freq 7 422 +/- 5 Hz Freq 8 152 +/- 5 Hz Stop and off 5 seconds, 3 - 1 second pulses and repeat Mode 2 will blink 2 Flashes every 2 seconds Note that due to the accuracy of the microprocessor generated signal, most units are within 1 Hz of the specified frequency.	3.5 min 3.5 min 3.5 min 3.5 min 3.5 min 3.5 min 3.5 min 3.5 min
Mode 3	Rife very low range Freq 1 125 +/- 5 Hz Freq 2 95 +/- 5 Hz Freq 3 72 +/- 5 Hz Freq 4 40 +/- 5 Hz Freq 5 20 +/- 5 Hz Freq 6 48 +/- 5 Hz Freq 7 160 +/- 5 Hz Freq 8 240 +/- 5 Hz Stop and off 5 seconds, 3 - 1 second pulses and repeat Mode 3 will blink 3 Flashes every 2 seconds	3.5 min 3.5 min 3.5 min 3.5 min 3.5 min 3.5 min 3.5 min 3.5 min
Mode 4	Rife Trio Freq 1 727 +/- 5 Hz Freq 2 787 +/- 6 Hz Freq 3 880 +/- 5 Hz Freq 4 700 +/- 5 Hz Freq 5 832 +/- 6 Hz Freq 6 760 +/- 5 Hz Freq 7 802 +/- 5 Hz Freq 8 776 +/- 6 Hz Stop and off 5 seconds, 3 - 1 second pulses and repeat Mode 4 will blink 4 Flashes every 2 seconds Note that due to the accuracy of the microprocessor generated signal, most units are within 1 Hz of the specified frequency.	3.5 min 3.5 min 3.5 min 3.5 min 3.5 min 3.5 min 3.5 min 3.5 min
	Note: The frequencies in this unit are far more accurate than the frequencies in Rife units that select the frequency using a dial, unless a digital readout is used.

While the unit has automatic timing and recycling for each frequency, it does not feature an automatic shutdown so that it can be used for continouos zapping. Power to the unit is supplied by a standard 9-volt battery and is controlled by a push-on / push-off switch. Frequency selection is by momentary contact push button switch. To change modes, simply press the mode switch. The battery and mode LED's will both come on at the same time. Release the switch and the next mode will start.

Description of Indicators ( Status, Mode/Battery ) and switches (ON/OFF) and Mode (mode change)

Power ON switch: (ON/OFF Button)
When the ON/OFF switch is pressed, the unit will come on and always starts out in Mode 1.

Status LED: (Status) located nearest the On/Off button
The status LED can be used to monitor normal operation and also to test the unit for correct operation. The Status LED will normally appear yellowish or orange but there are exceptions. If the battery is completely dead or missing, the LED will be off or dark. If for some reason, the output fails, the LED will either be solid green or red.
To test the unit when operating, the unit should be on and operating with the copper paddles connected but not touching. In this condition, the LED will appear yellow or amber because it is flickering between red and green.
Touching the copper paddles together should cause the LED to show almost completely red due to the current load being pulled by the short circuit. This is an indicaton that the zapper output is functioning properly and providing sufficient output for best results.

Mode change switch: ( MODE button )
Pressing this button at any time will change the current mode and will also restart the timer.
Each time that the mode switch is pressed, it will cycle to the next mode which can be observed by watching the Mode/Battery LED for the number of flashes produced.

Mode LED: (Battery / Mode) which is the Lower LED
The mode LED flashes the corrosponding number of flashes for the mode that it is currently operating in as described in the Mode table above.

zapper

Hulda Clark Zapper is
not FDA approved for human or animal use.

Due to FDA restrictions,
Hulda Clark Zappers are not sold or intended for
human use or on animals.

The zappers below are intended to be used to lower levels
of bacteria, parasites, and other organisms in standing
water such as cooling towers, ponds, fountains, water containers, or similar water tanks.

Zappers may also be used for checking oscilloscopes
or items such as small loud speakers,
but not for calibration purposes.

By purchasing any zapper or accessory from this site
you are agreeing that these products are sold
"not intended for use on humans or animals".

Do not use for drinking water, potable water,
in swimming pools, or for food preparation.

ParaZapper™M1

Not available yet, expected by Jan. 30, 2009

Not sold for use on humans or animals due to FDA requirements.

For the user who wants more frequencies and power.
With Stronger output than standard zappers, multiple repeating frequency cycles ion each range, Low Battery Indicator, Dual Frequency ranges, and a multicolor Status Indicator.

This is a multi-frequency zapper that is expected to provide better overall results.
Instructions for use on humans are not included but are available.

This model not available yet


Warranty Satisfaction Privacy	About us	Shipping	Technical information	Other zapper products

Usage

Using these devices for eliminating parasites from water is easy but is not 100 percent effective.
Before and after microscopic examination of pond water samples show significant reduction of microbial content after usage.

Normal application is to place the electrodes into the water, further apart is better.
The unit is then turned on 7 minutes and off for 20 minutes and repeated 3 or 4 times.

Do not use for drinking water, potable water, or in swimming pools.

Contact Webmaster:
Contact Sales: sales@paradevices.com

Our normal phone hours are 9:30 AM to 3:00 PM Central time weekdays
however, if you need to reach us at other times, call anyway.
We do not take orders by phone and can not make recommendations for use with humans or animals.
If we are not in, leave a name and phone number, we will call back.

Phone# 1-866-765-5116 Nationwide Tollfree
--or-- 205-856-3909 Alabama Local
Both numbers are for the same phone line.

Notice: On advice of counsel, we are required to inform you that the statements and claims on this web site have not been evaluated by the Food and Drug Administration and are not intended to diagnose, treat, cure or prevent any disease -- not for use on humans or with pets. These battery powered devices are not offered or intended for human use or to diagnose or prescribe for medical or psychological conditions nor to claim to prevent, treat, mitigate or cure such conditions, nor to recommend specific products as treatment of disease or to provide diagnosis, care, treatment or rehabilitation of individuals, or apply medical, mental health or human development principles. The devices discussed herein have not undergone evaluation and/or testing by the United States Food and Drug Administration or like agency of any other country. Risks that might be determined by such testing are unknown. The information on this site is not a substitute for medical or veterinary advice.

Historical references
parazapper.com
paradevices.com
hulda-clark-parasite-zapper.com

visits to this page

parazapper site visits